Our Flexible COB LED Strip Light series creates a seamless line of light from start to finish. The all-new strip design uses flip-chip LEDs to eliminate visible LED dots (hot spots). The all-new chip-on-board technology not only improves light quality but also improves the thermal management and flexibility of the strip. The smaller LEDs can be packed tighter and weigh much less than the bulkier LEDs, creating a strip that can work around the needs of your application. The spotless output makes the COB LED strips ideal for narrow applications like display cases and backlighting, or where reflective surfaces such as granite and tile are used.
Getian supply professional and honest service.
High Output, Quality Light
The COB LED Flex Strips hold a whopping 512 LEDs per Meter which creates Lumens/M of smooth continuous light emitting at 180 degrees. The wide viewing angle and a continuous stream of light make this a serious upgrade from the flexible strip lights you are used to.
Colors
LEDSupply&#;s COB LED strips are offered in: Red, Green, Blue, Warm White K, Neutral White K & Cool White K.
Custom Lengths
Unlike most suppliers, we offer COB LED strip lights in smaller 3-foot increments up to 16.4 feet long (1 Reel = 5M). Some applications might need a shorter section of strips which is why the LED strips can be cut every few inches. You can cut the strip along the cut marks which feature a thin black line running over solder pads. Max Run Length = 2 full reels - 32.8ft.
End-to-End Connections
When there is a break in your application you can still run one strip to another using 20-24 gauge wire or LED strip connectors. TAKE NOTE: COB LED Strip's maximum run length is 32.8 feet (2 reels). After the maximum run length, the voltage drop becomes too great and you will lose light and efficiency from your system. If your application needs more than the maximum run length you will have to get another power supply or run wires from the extra strip directly back to the first power supply (wiring in parallel).
Connections can be made by soldering wire in between strips or by using solderless clamps. Only one end of the strips comes with a plug on it (except for full reel lengths which have 2) so if you want to make more connections you will need to solder or use strip connectors. Here is a good tutorial on wiring the strips together if you'd like more information.
Power
The strips need 24VDC input. This requires either a battery or 24V Power Supply. The strips run at roughly 14 Watts/M. Please make sure you have enough wattage when running your specified length. The below wattage chart has accurate wattage calculations for each length shown.
Detailed Wattage Table for 24V Spotless COB LED Strips LENGTH WATTAGE Feet (Ft) Meters (M) COB Strip Wattage (W) 1 0. 5.9 2 0. 10.9 3 0. 16 6 1. 27.8 9 2. 40.8 12 3. 49.7 16.4 (Full Roll) 5 (Full Roll) 58.4Connecting to power can easily be done with simple wire-to-wire techniques such as soldering, wire nuts, electrical tape, etc. If you have a plug-in adapter with a barrel plug on the end, these screw-in terminal power plugs help turn the wire leads into a simple plug-in connection.
Dimming
The strips are fully dimmable and can be used with 24V PWM dimmers. The dimmer will go between your power supply and strips. Find compatible controllers below in the PWM Dimmers section.
If you require an AC Dimming Control from Lutron or Leviton, use a dimmable power supply.
Need Help with LED Strips?
Guide to LED Strip Lights
DIY Tutorial: Accent Lighting with LED Flex Strips
DIY Tutorial: Setting Up Color Changing LED Strips
P/N
Color
Kelvin (K), Wavelength (nm)
Beam Angle
°
Luminous Flux
(lm/m>
CRI
Efficacy
(lm/w)
Input Voltage
(VDC)
Power
(W/m)
LO-10COB-WWT
Warm-White
K
180°
>90
100
24
14
LO-10COB-NWT
Neutral-White
K
If you are looking for more details, kindly visit Buy 12V COB LED Chip.
180
>90
100
24
14
LO-10COB-CWT
Cool-White
K
180
>90
100
24
14
LO-10COB-RED
RED
N/A
180
-
80
-
24
14
LO-10COB-GRN
Green
N/A
180
-
80
-
24
14
LO-10COB-BLU
Blue
N/A
180
-
80
-
24
14
Remote dimmer
Small, in-line dimmer that plugs into the outlet side of the 12 volt transformer. The system controls our kitchen under counter lighting and is mounted behind a kitchen drawer. The remote is small and easy to use and the mounting location does not affect it. 100% lights when cooking and less other times. This is my first and it works better than I thought it would. Simple to install and simple to use.
JRK