If you are looking for more details, kindly visit resistor manufacturing factory.
Implementing decoupling schemes, efficient grounding, circuit safety measures, and capturing a schematic diagram are a few of the best electronic design practices. In this article, we will discuss the best circuit design practices that can build a well-planned board.
Highlights:
A well-designed circuit board is essential for creating reliable and high-performing electronic devices.
When designing your circuit, be mindful of the manufacturing process. Consider aspects like component size and placement, trace routing, and the usage of vias.
Using a standard schematic format can make it easier for others to understand and troubleshoot your design.
Document your design thoroughly, including creating schematics, layout drawings, and bills of materials for future troubleshooting and maintenance.
Test your design thoroughly, including building a prototype and testing it under various conditions using simulation software.
Let&#;s dive right into it with block diagrams.
Original
p
720p
540p
224p
Captions
Your first step in designing an electronic circuit is to develop a detailed requirements specification that covers all aspects of circuit design including:
All this should be done keeping in mind the available budget. The next step is to build block diagrams that provide an overview of the circuit functioning and component groupings. Block diagrams are crucial for successful electronic circuit design and act as a reference material for future circuit analysis.
They also allow for a divide-and-conquer strategy where the diagram is broken down into different functional sections, each performing a specific task that can be implemented and tested in isolation. Knowledge and understanding of the operation of each of these blocks are necessary. Some blocks may have signal conditioning circuits so that the output can be read easily by the data acquisition system. For example, output from an LDR (light-dependent resistor) sensor needs to be converted to a voltage range that can be easily read by the microcontroller ADC. Circuits in these blocks could also be replicated in other designs requiring similar functions, promoting design reuse. To learn more about design reuse, see auto grouping of repetitive PCB design blocks.
Power supplies are not always stable due to non-ideal operating conditions and the output voltage can fluctuate or develop noise which can cause the circuit to misbehave or even fail.
Decoupling capacitors are used in parallel to the power supply to decouple the incoming AC signals from the DC signals. They filter out any spikes that occur and protect the different ICs in the circuit. The capacitor starts charging from the power supply until it reaches the supply voltage and holds that value. If there is a drop in the supply voltage, the value of what constitutes a high (state high) will decrease. At the same time, these spikes bring the ground to a slight positive voltage, causing the value of what constitutes as low (state low) to increase.
This makes it harder to differentiate between 1 and 0, closing your eye diagram. It also negatively impacts the power integrity of your design. Adding a suitable capacitor across the supply compensates for the voltage drop. This is because the capacitor voltage does not change instantaneously and provides the supply to the IC. Similarly, the capacitor charges from the spikes and discharges to maintain a steady voltage across it, ensuring that the spikes do not affect the IC supply. They are often placed close to the IC power supply points, and generally should be as close as possible.
A coupling capacitor is used in the path of a signal. It passes the desired AC signal and blocks out the unwanted DC element. They are common in audio and RF applications.
A bypass capacitor is used in parallel to the output signal in order to filter out low-frequency noise by shunting it to the ground and providing a pure DC signal.
Electrolytic capacitors mostly work well for low-frequency applications where more charge is to be delivered. Ceramic and MLCC capacitors work well for high-frequency applications. Tantalum capacitors are highly stable at high capacitance values and are used more in coupling applications. The choice of the capacitor must be made based on the circuit performance requirements, ESR, ESL, and cost constraints.
A good circuit design practice is to choose suitable capacitors based on your application and ensure their ideal placement.
Digital ICs work with certain logic levels to determine whether the input is interpreted as 0 or 1. For a VCC of 5V, voltage levels from 5V to 2.8V are considered logic 1, and 0 to 0.8 as logic 0. The voltage range between 0.9 to 2.7V will be an indeterminate region and the chip will interpret it either as a 0 or as a 1 causing the IC to behave incorrectly. This is called the floating state.
To prevent this, pull-up or pull-down resistors are used while designing electronic circuits that use digital ICs, microcontrollers, and switches. Pull-up resistors are used to fix the voltage close to VCC and pull-down resistors to pull the voltage close to GND point. Modern microcontrollers are now equipped with internal pull-up and pull-down resistors that can be activated using a code. Please check the datasheet and decide accordingly if these resistors need to be used or eliminated.
Zero ohm resistors can be used to modify the circuit even after its construction. These resistors are used as a bridge to route tracks optimally on a board.
As a circuit board designer, you can make PCBs with multiple configurations and functionalities. Most often these configurations interfere with each other and cannot all coexist in a circuit. Hence, based on requirements, different sections of the PCB can be disabled or enabled easily by unsoldering or adding zero resistors accordingly.
You can divide the circuit into multiple sections by using zero resistors. This is helpful in isolating faulty segments that need troubleshooting. For example, it is easy to find noisy blocks and traces that cause crosstalk without having to cut up the circuit.
A section of the circuit might need a series resistance whose value needs adjustments and isn&#;t fixed yet. Until the value is finalized, zero resistors can be used temporarily. Zero resistance pads also serve as a test or debug point to measure various parameters like voltage, current, etc.
SMD zero resistors facilitate continuous connection and are used to replace jumpers. This will allow for an efficient single-layer board design instead of a double-layer. They are much cheaper than DIP switches or berg jumpers. Zero ohm resistors are also used as circuit breakers during supply overload preventing circuit damage.
Due to the reasons mentioned above, using zero resistances during prototyping in the initial design phase is a good practice.
In RF circuits, zero resistors can be inserted into an RF feed in series with the antenna trace. As the antenna is tuned, it can be replaced with other values. It is also used as a matching element in some RF applications.
Wired resistances i.e. traces connected by zero ohms work well for digital circuits. However, high-speed circuits will not work due to the high value of their parasitic inductance. The maximum permissible current, the enclosure type, the footprint on the PCB, the parasitic inductance, and the capacitance of the resistor are different parameters to be looked at while choosing a zero resistor.
Mixed-signal circuits are hybrid circuits that combine both analog and digital circuitry in a semiconductor die. This is also referred to as system-in-package. Depending on the design requirements, you should make use of modern low-cost microcontrollers as they have several built-in features. The most commonly used microcontroller peripherals are timers, pulse-width modulators (PWM), analog-to-digital converters (ADC), digital-to-analog converters (DAC), and serial/SPI/ I2C communication interfaces.
They can be easily programmed to function according to the requirements. This will avoid overkilling your circuit with too many discrete components to perform the same task. Integrating appropriate digital ICs and analog circuit sections with a microcontroller will increase the performance efficiency of the circuit while reducing its size and cost. A block diagram of a microcontroller is shown below.
Building a circuit that saves energy is important, especially for those which are operated with batteries. PWM is a type of modulation where the pulse width of a signal is modified based on the duty cycle.
A PWM signal with a 75% duty cycle will stay ON for 75% and OFF for 25% of the total time period, thus reducing the mean output power consumption. These signals can be generated using a reliable microcontroller or NE555 IC. It can be employed to save energy in simple LED and motor driving circuits. PWM waveforms are also used in power converter(s) topology to design highly efficient, lighter, and inexpensive switched-mode power supply designs.
All signal references should have individual traces to the common ground. As shown in the schematic below. The ground pins of different chips in the circuit must be connected to the common node separately rather than interconnecting each of them and then tying it with common ground. This will avoid humming noise.
The most effective approach for ensuring proper grounding in mixed-signal boards is to employ a single ground plane without any splits. Additionally, the return paths should be as short as possible to minimize interference or crosstalk between analog and digital components. Designate a part of the ground plane for digital ground and the rest for the analog ground without any splits.
For more information, please visit film type resistor.
Ground loops are caused when multiple ground points in a circuit are at different potentials. They are a major cause of noise, humming, and interference in consumer electronics. This can be avoided by ensuring that all vulnerable signal circuits are referenced to one point as ground. These circuits operate at high-speed and low-voltage levels, making them more susceptible to noise. The use of differential signaling can also provide rejection of ground-induced interference.
EMI can be reduced by having optimum ground plane separation and the shortest possible signal return paths. Shielded inductors will ensure EMC by cutting down sharp current transients.
Protecting circuit connections from ESD is extremely essential if the product is used in harsh conditions. Metal-oxide varistors, TVS (transient voltage suppressor) diode arrays, clamping diodes, and GDTs (gas discharge tubes) can be used to safeguard from ESD. Between the diodes and ICs, a resistance of a few tens of ohms can be placed to dissipate voltage surge. This should be especially implemented at communication interface connections, user button contacts, and other sensitive input/output connections.
Reverse polarity protection in a circuit can be provided by different types of diodes or by using FET circuits. Diodes usage is mostly suitable for low-power applications.
For overvoltage protection, voltage limiters can be used in conjunction with electronic fuse chips and thermistors. Modern ICs now come with built-in protection circuits. Examples of voltage limiters are varistors, TVS diodes, and diode circuits (clipping and clamping). Fusechips can be either hotswap circuit ICs or power controllers.
Protection diodes should also be used when relays are being driven by semiconductors. If the power to the relay coil is shut off suddenly, the coil will generate a voltage spike that can damage the rest of the circuit. A flyback diode acts as a snubbing circuit, providing a discharge path for the coil in order to protect your circuit. Using microcontrollers for a protective shutdown circuitry should be avoided as they might freeze.
High-voltage capacitors used in the circuit must be provided with proper discharge paths. If devices in a circuit are deriving power from a network, a good understanding of class X/class Y safety capacitors and their proper placement is essential. These capacitors are used to filter AC signals and reduce EMI as shown in the figure below. They also mitigate the adverse effects of voltage transients and overvoltage surges.
Class X capacitors are typically placed between the line and neutral of the AC supply to reduce EMI/RFI due to differential mode noise. Class Y capacitors are ideally placed in between the AC supply and ground to minimize common mode noise. There are varying standards and classifications for safety capacitors that indicate their threshold capacities. You should choose the right capacitors based on the design needs.
You must choose optimal combinations of the above-mentioned protection schemes by considering error probabilities, reliability requirements, and PCB space and cost constraints.
When you&#;re working with high voltages, proper PCB grounding techniques such as galvanic isolation must be provided to avoid electric shocks. This prevents potentially damaging currents from passing through the operator&#;s body or to other parts of the circuit.
Galvanic isolation is also used when two sections of a circuit have different ground potentials and a signal needs to be transferred between them. It prevents the flow of unwanted AC and DC currents between the two parts. Isolation breaks these ground loops that cause signal inaccuracies between the two systems, maintaining communication integrity. A popular option is to use transformers for stepping up/down voltages along with using electric fuses. The exchange of information between isolated sections is provided by using optoisolators, hall sensors, capacitors, or relays.
6 Chapters - 53 Pages - 60 Minute Read
The components need to be selected based on the design requirements and adequate margins. Many different packages are available on the market &#; through-hole, surface mount, panel mount, and chassis mount to take advantage of various requirements.
Consider these tips while choosing components for your electronic circuit design:
The next important part of the electronic circuit design process is to draw the schematic diagram using EDA tools like Altium, KiCAD, and Cadence Allegro. These tools provide several features like schematic capture, creating electronic components, simulating complex circuit functions, and BOM creation. They also include PCB layout packages, component footprints, 3D views, and output of manufacturing files. Choose an EDA tool that is comfortable and which provides adequate design support.
Capturing the schematics forms the basic foundation on which the rest of the design documents are built. There needs to be information synchronization between the schematic, netlist, and layout. For the best schematic design practices, see how to draw and design a schematic.
10 Chapters - 40 Pages - 45 Minute Read
Verifying and testing individual circuit blocks of the design that are critical using simulation software is the next step in electronic circuit design. Many EDAs provide this option where the correct functionality of the block can be tested. You can make necessary changes in case the circuit doesn&#;t function as per requirement.
Simulation software has limitations and sometimes a good circuit may not provide accurate results on the system. Therefore, it is recommended to rig up the circuit section physically on a breadboard to test its functionality. If there are any errors in any circuit block, you can troubleshoot and rectify the issue in the next design iteration.
Another very important design practice is to document every step of the design process. This includes all details like reasons for choosing a solution, a component, a logic table, and undertaking special considerations.
The advantages of keeping notes are:
After simulations and functionality testing, you can now route the PCB layout. Appropriate footprints need to be used/created for the parts and linked to the component before generating the netlist. The netlist is then imported to a layout editor for routing.
You need to ensure effective component placement and grouping to facilitate optimized routing. This should be done by taking into consideration the power, thermal, and electrical variations of the circuit. See mastering the art of PCB design basics to learn about stack-up preparation, footprint inspection, routing, fabrication, and assembly drawings. It also gives an overview of the DFM and DFA quality checks that are carried out for manufacturing a good quality PCB.
Key takeaways:
Effective electronic circuit design practices are essential for building well-planned circuit boards.
Block diagrams help define specifications and component groupings, facilitating a divide-and-conquer strategy in circuit design.
Proper placement of decoupling, coupling, and bypass capacitors is critical to stabilize power supplies and prevent signal interference.
Pull-up, pull-down, and zero resistors are used to maintain logic levels in digital ICs and enable circuit modification and troubleshooting.
Utilizing microcontrollers and mixed-signal circuits can enhance circuit performance efficiency and reduce component count.
PWM signals can be used to reduce power consumption, particularly in battery-operated circuits.
Strategic signal return paths and grounding techniques help prevent EMI and ground loops.
Safety measures such as protection from ESD, reverse polarity, transients, and over-voltages are crucial for circuit reliability.
Component selection should consider datasheets, obsolescence, derating, and overrating, while using standard values and avoiding long lead times.
Capturing schematics and verifying them using EDA tools, followed by simulations and functional tests, are essential for verifying circuit performance.
Documentation is essential for efficient issue resolution and knowledge transfer across teams.
By following these practices diligently, engineers can design efficient and reliable electronic circuits, ensuring optimal performance and longevity.
Designing electronic circuits can be a daunting task but if these practices are followed diligently along with correct documentation, you will be able to hone the necessary skills. Share your best electronic circuit design practices and top tips in the comment section below.
Visit our PCB design services page to learn more about our capabilities.
This family of high resistance (10M Ohms to 1 Tera Ohms) resistors employs a thick film resistive element and is designed for long term stability and low TCR (temperature coefficient of resistance) which are compatible with high volume SMT applications. TCR&#;s as low as +/-25ppm and tolerances as tight as +/-1% are available.
Standard EIA size packages , , , , and can handle power up to 2 Watts. These are non-magnetic resistors and thus are well suited for nonmagnetic applications.
For resistors operating in high temperature environments, we have two temperature options up to +155C or +300C. Their platinum silver terminations are designed are compatible with soldering, epoxy bonding, or wire bonding applications. The wide range of electrical and mechanical characteristics allow for design flexibility.
We can design our high temperature resistors for specific voltage requirements by trimming these thick film resistors. Contact our applications engineers to discuss high voltage or high temp ( +300C) applications.
If you want to learn more, please visit our website all types of resistors.